--------------------------------------------------------------------
-- CISCO-FRAME-RELAY-MIB.my
-- Cisco Frame Relay MIB file, providing Frame Relay specific
-- information that are either excluded by RFC 1315 (FR DTE MIB)
-- or specific to Cisco products.
--
-- January 1996, Chifei Cheng
--
-- Copyright (c) 1996, 1999, 2000, 2001 by cisco Systems, Inc.
-- All rights reserved.
--
---------------------------------------------------------------------- Note:
-- Until future change, it is no intention for this MIB to cover
-- every Frame Relay related feature, configuration statement, or
-- exec command display. The focus is to provide key information
-- that are unavailable in any of the existing MIB's, but are
-- currently available through the Frame Relay show commands and/or
-- configuration displays.CISCO-FRAME-RELAY-MIB DEFINITIONS::=BEGINIMPORTSMODULE-IDENTITY,
OBJECT-TYPE,Counter32,Integer32,IpAddressFROM SNMPv2-SMI
MODULE-COMPLIANCE,OBJECT-GROUPFROM SNMPv2-CONF
TEXTUAL-CONVENTION,DisplayString,TruthValueFROM SNMPv2-TC
ciscoMgmt
FROM CISCO-SMI
InterfaceIndexFROM IF-MIB
ifIndex
FROM RFC1213-MIB
frDlcmiEntry,frCircuitEntry,frCircuitIfIndex,frCircuitDlci
FROM RFC1315-MIB;-- All table indicies in this MIB that involve interface index and
-- DLCI are derived from frCircuitIfIndex and frCircuitDlci
-- respectively from RFC 1315.ciscoFrameRelayMIB MODULE-IDENTITYLAST-UPDATED"200010130000Z"ORGANIZATION"Cisco Systems, Inc."CONTACT-INFO" Cisco Systems
Customer Service
Postal: 170 W Tasman Drive
San Jose, CA 95134
USA
Tel: +1 800 553-NETS
E-mail: cs-framerelay@cisco.com"DESCRIPTION"Cisco Frame Relay MIB"REVISION"200010130000Z"DESCRIPTION"(1) Added objects of FR Switching, FR Fragmentation
and FR/ATM Interworking.
(2) Objects for per PVC I/O rate is added to
cfrExtCircuitTable"REVISION"200005220000Z"DESCRIPTION"(1) Added ELMI subgroup for ELMI objects."REVISION"200005160000Z"DESCRIPTION"(1) Added Traffic Shaping parameter objects to
cfrExtCircuitTable.
(2) Deprecated cfrSvcMinThruputOut and
cfrSvcMinThruputIn. Added cfrExtCircuitMinThruputOut
and cfrExtCircuitMinThruputIn in cfrExtCircuitTable
inorder to make them applicable to both PVC/SVC.
(3) Added cfrExtCircuitBandwidth object to
cfrExtCircuitTable."REVISION"200004260000Z"DESCRIPTION"(1) add an integer value for cfrMapPayloadCompressType;
(2) reword the Description statements for
{ cfrMapPayloadCompressType,
cfrExtCircuitUncompressIns,
cfrExtCircuitUncompressOuts }
so that they are not limited to software compression."REVISION"9908210000Z"
DESCRIPTION"(1) Added cfrExtCircuitUncompressOuts and
cfrExtCircuitUncompressIns to the circuit subgroup;
(2) Added cfrMapRtpHdrCompress and cfrMapPayloadCompressType
to the mapping subgroup;
(3) cfrMapPayloadCompress becomes deprecated, obsoleted
by cfrMapPayloadCompressType;
(4) frCircuitSentOctets and frCircuitReceivedOctets
per RFC1315 will reflect the number of bytes in Frame Relay
frames sent to and received from the physical layer. Same
effect is applied to ifOutOctets and ifInOctets as well
when ifIndex refers to a Frame Relay subinterface."REVISION"9608150000Z"DESCRIPTION"Initial version of this MIB module."::={ ciscoMgmt 49}ciscoFrMIBObjects OBJECTIDENTIFIER::={ ciscoFrameRelayMIB 1}-- Subgroups:
-- The objects include four subgroups on the topics of
-- o LMI (Local Management Interface, see ANSI T1.617 Annex D and
-- the Frame Relay Specification with Extensions by DEC,
-- NT, StrataCom, and Cisco.),
-- o Virtual circuits,
-- o Circuit mapping information,
-- o SVC (switched virtual circuits, see CCITT/ITU Q.933 and
-- Q.922.),
-- o ELMI (Enhanced Link Management Interface) objects,
-- o Fragmentation objects,
-- o Frame Relay/ATM Network Interworking objects,
-- o Frame Relay/ATM PVC Service Interworking objects, and
-- o Frame Relay Switching objects.cfrLmiObjs OBJECTIDENTIFIER::={ ciscoFrMIBObjects 1}cfrCircuitObjs OBJECTIDENTIFIER::={ ciscoFrMIBObjects 2}cfrMapObjs OBJECTIDENTIFIER::={ ciscoFrMIBObjects 3}cfrSvcObjs OBJECTIDENTIFIER::={ ciscoFrMIBObjects 4}cfrElmiObjs OBJECTIDENTIFIER::={ ciscoFrMIBObjects 5}cfrFragObjs OBJECTIDENTIFIER::={ ciscoFrMIBObjects 6}cfrConnectionObjs OBJECTIDENTIFIER::={ ciscoFrMIBObjects 7}DlciNumber ::=TEXTUAL-CONVENTIONSTATUScurrentDESCRIPTION"Numerical format of Data Link Connection Identifier
(DLCI) in decimal, identical to the 'DLCI' as INTEGER
of 0..DLCINumber in RFC1315. The maximum value depends
on Frame Relay implementation, which is currently set
to be 1023 for 2-octet address format per UNI
Implementation Agreement FRF.1."SYNTAXINTEGER(0..1023)CfrMapProtocols ::=TEXTUAL-CONVENTIONSTATUScurrentDESCRIPTION"Cisco link types (network protocols) that run
over Frame Relay. Associated values, except for
wildcard, match assigned values of internal software
respectively."SYNTAXINTEGER{arp(1),serialArp(6),ip(7),xns(10),novell(11),apollo(12),vines(13),appletalk(16),ieeeSpanning(18),
decnet(22),clns(25),rsrb(37),bridge(38),stun(39),frArp(40),uncompressedTcp(47),compressedTcp(48),llc2(49),frSwitch(53),dlsw(63),nhrp(74),compressedRtp(83),wildcard(999)-- either means no applicable type for-- the circuit or means point-to-point}-- LMI sub-group {cfrLmiTable OBJECT-TYPE
SYNTAXSEQUENCEOF CfrLmiEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Table of Frame Relay LMI information that are
either supplemental to the frDlcmiTable of RFC 1315
or specific to Cisco's implementation."REFERENCE"American National Standard T1.617-1991, Annex D"::={ cfrLmiObjs 1}cfrLmiEntry OBJECT-TYPESYNTAX CfrLmiEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Each entry of the table contains information
of Frame Relay LMI over one physical interface.
They are mostly FR generic and some Cisco specific."AUGMENTS{ frDlcmiEntry }::={ cfrLmiTable 1}
CfrLmiEntry ::=SEQUENCE{
cfrLmiLinkstatus INTEGER,
cfrLmiLinkType INTEGER,
cfrLmiEnquiryIns Counter32,
cfrLmiEnquiryOuts Counter32,
cfrLmiStatusIns Counter32,
cfrLmiStatusOuts Counter32,
cfrLmiUpdateStatusIns Counter32,
cfrLmiUpdateStatusOuts Counter32,
cfrLmiStatusTimeouts Counter32,
cfrLmiStatusEnqTimeouts Counter32,
cfrLmiN392Dce INTEGER,
cfrLmiN393Dce INTEGER,
cfrLmiT392Dce INTEGER}-- Note: for LMI type, i.e. ANSI or Cisco, see frDlcmiState
-- of RFC 1315. Also, for LMI parameters for DTE not listed here,
-- e.g. T391, N391, N392, and N393, see RFC 1315.
--
-- Although based on the current logic the value for
-- cfrLmiDLstatus is equivalent to ifOperStatus, the object
-- remains herein for future possible development change.cfrLmiLinkstatus OBJECT-TYPESYNTAXINTEGER{up(1),down(2)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION
"Data link status via LMI."::={ cfrLmiEntry 1}cfrLmiLinkType OBJECT-TYPESYNTAXINTEGER{dte(1),dce(2),nni(3)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Frame Relay link type."::={ cfrLmiEntry 2}cfrLmiEnquiryIns OBJECT-TYPESYNTAXCounter32UNITS"messages"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Number of Status Enquiry messages received."::={ cfrLmiEntry 3}cfrLmiEnquiryOuts OBJECT-TYPESYNTAXCounter32UNITS"messages"
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Number of Status Enquiry messages sent."::={ cfrLmiEntry 4}cfrLmiStatusIns OBJECT-TYPESYNTAXCounter32UNITS"messages"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Number of Status messages received."::={ cfrLmiEntry 5}cfrLmiStatusOuts OBJECT-TYPESYNTAXCounter32UNITS"messages"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Number of Status messages sent."::={ cfrLmiEntry 6}cfrLmiUpdateStatusIns OBJECT-TYPESYNTAXCounter32UNITS"messages"MAX-ACCESSread-onlySTATUScurrent
DESCRIPTION"Number of Update Status messages received."::={ cfrLmiEntry 7}cfrLmiUpdateStatusOuts OBJECT-TYPESYNTAXCounter32UNITS"messages"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Number of Update Status messages sent"::={ cfrLmiEntry 8}cfrLmiStatusTimeouts OBJECT-TYPESYNTAXCounter32UNITS"times"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Number of times when timeout occurred on waiting
for Status message"::={ cfrLmiEntry 9}cfrLmiStatusEnqTimeouts OBJECT-TYPESYNTAXCounter32UNITS"times"MAX-ACCESSread-onlySTATUScurrent
DESCRIPTION"Number of times when timeout occurred on waiting
for Status Enquiry message"::={ cfrLmiEntry 10}cfrLmiN392Dce OBJECT-TYPESYNTAXINTEGER(0..10)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"LMI error threshold for DCE interface.
For DTE, value becomes 0."::={ cfrLmiEntry 11}cfrLmiN393Dce OBJECT-TYPESYNTAXINTEGER(0..10)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"LMI monitored event count for DCE interface.
For DTE, value becomes zero (0)."::={ cfrLmiEntry 12}cfrLmiT392Dce OBJECT-TYPESYNTAXINTEGER(0..30)
UNITS"seconds"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"DCE polling verification timer for DCE interface
For DTE, the value becomes zero (0)."::={ cfrLmiEntry 13}-- end LMI subgroup }-- Circut sub-group {cfrCircuitTable OBJECT-TYPESYNTAXSEQUENCEOF CfrCircuitEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Table of descriptive and statistics information
that are generic to Frame Relay virtual circuits."::={ cfrCircuitObjs 1}cfrCircuitEntry OBJECT-TYPESYNTAX CfrCircuitEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Each entry of the table contains information of a
circuit that are not included in frCircuitTable of
RFC1315 but are generic to Frame Relay."AUGMENTS{ frCircuitEntry }
-- indexed by { frCircuitIfIndex, frCircuitDlci }::={ cfrCircuitTable 1}
CfrCircuitEntry ::=SEQUENCE{
cfrCircuitDEins Counter32,
cfrCircuitDEouts Counter32,
cfrCircuitDropPktsOuts Counter32,
cfrCircuitType INTEGER}cfrCircuitDEins OBJECT-TYPESYNTAXCounter32UNITS"packets"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Number of packets received with the Discarded
Eligibility indictor (the DE bit) set."::={ cfrCircuitEntry 1}cfrCircuitDEouts OBJECT-TYPESYNTAXCounter32UNITS"packets"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Number of packets transmitted with DE bit set."::={ cfrCircuitEntry 2}
cfrCircuitDropPktsOuts OBJECT-TYPESYNTAXCounter32UNITS"packets"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Number of discarded packets that were to be sent."::={ cfrCircuitEntry 3}cfrCircuitType OBJECT-TYPESYNTAXINTEGER{pvc(1),-- permanent virtual circuitsvc(2)-- switched virtual circuit}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Basic circuit type"::={ cfrCircuitEntry 4}-- Cisco specific circuit information:cfrExtCircuitTable OBJECT-TYPESYNTAXSEQUENCEOF CfrExtCircuitEntry
MAX-ACCESSnot-accessible
STATUScurrentDESCRIPTION"Table of Cisco implementation specific FR
circuit information. This is a Cisco extension
for the frCircuitTable of RFC 1315."::={ cfrCircuitObjs 2}cfrExtCircuitEntry OBJECT-TYPESYNTAX CfrExtCircuitEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Each entry of the table contains information
of a Frame Relay virtual circuit that are specific
to Cisco implementation."AUGMENTS{ frCircuitEntry }-- indexed by { frCircuitIfIndex, frCircuitDlci }::={ cfrExtCircuitTable 1}
CfrExtCircuitEntry ::=SEQUENCE{
cfrExtCircuitIfName DisplayString,
cfrExtCircuitIfType INTEGER,
cfrExtCircuitSubifIndex InterfaceIndex,
cfrExtCircuitMapStatus INTEGER,
cfrExtCircuitCreateType INTEGER,
cfrExtCircuitMulticast TruthValue,
cfrExtCircuitRoutedDlci DlciNumber,
cfrExtCircuitRoutedIf InterfaceIndex,
cfrExtCircuitUncompressIns Counter32,
cfrExtCircuitUncompressOuts Counter32,
cfrExtCircuitFECNOuts Counter32,
cfrExtCircuitBECNOuts Counter32,
cfrExtCircuitMinThruputOut Integer32,
cfrExtCircuitMinThruputIn Integer32,
cfrExtCircuitBcastPktOuts Counter32,
cfrExtCircuitBcastByteOuts Counter32,
cfrExtCircuitBandwidth Integer32,
cfrExtCircuitShapeByteLimit Integer32,
cfrExtCircuitShapeInterval Integer32,
cfrExtCircuitShapeByteIncrement Integer32,
cfrExtCircuitShapePkts Counter32,
cfrExtCircuitShapeBytes Counter32,
cfrExtCircuitShapePktsDelay Counter32,
cfrExtCircuitShapeBytesDelay Counter32,
cfrExtCircuitShapeActive TruthValue,
cfrExtCircuitShapeAdapting INTEGER,
cfrExtCircuitTxDataRate INTEGER,
cfrExtCircuitTxPktRate INTEGER,
cfrExtCircuitRcvDataRate INTEGER,
cfrExtCircuitRcvPktRate INTEGER}cfrExtCircuitIfName OBJECT-TYPESYNTAXDisplayStringMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The textual name of the main interface or the
subinterface that this DLCI is associated with.
This is the same name string of an interface used
in the configuration and all console displays,
such as 'serial 0', 'serial 3/0.3', etc."::={ cfrExtCircuitEntry 1}cfrExtCircuitIfType OBJECT-TYPESYNTAXINTEGER{mainInterface(1),pointToPoint(2),-- subinterfacemultipoint(3)-- subinterface
}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Type of the subinterface this DLCI is associated
with, if configured."::={ cfrExtCircuitEntry 2}cfrExtCircuitSubifIndex OBJECT-TYPESYNTAXInterfaceIndexMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"For value greater than zero (0), it indicates
the network management interface index
for the subinterface associated with
this DLCI. Value 0 means the DLCI is not
associated with any subinterface."::={ cfrExtCircuitEntry 3}cfrExtCircuitMapStatus OBJECT-TYPESYNTAXINTEGER(0..2047)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The mapping protocols (internally considered as
the 'link type') applied on this circuit.
The value ranges from 0 to 2047.
For point-to-point DLCI, the value stays zero.
Otherwise, the value is a sum. It initially takes
the value zero, then, for each type of Protocol,
2 raised to a power is added to the sum.
The following table presents respective power and
equivalent value for each applicable type:
Protocol Power Value
-------- ----- -----
IP 0 1
IPX 1 2
Appletalk 2 4
XNS 3 8
VINES 4 16
DECnet 5 32
CLNS 6 64
Bridging 7 128
RSRB 8 256
STUN 9 512
LLC2 10 1024
For example, value 3 means the circuit's mapping
protocols include IP and IPX. (3 = 2**1 + 2**0,
where 0 corresponds to IP and 1 to IPX.) Value 0
means there is currently no mapping protocol for
the circuit.
See cfrMapTable for more mapping information."::={ cfrExtCircuitEntry 4}cfrExtCircuitCreateType OBJECT-TYPESYNTAXINTEGER{dynamic(1),-- PVC established through LMI-- or an SVC established through-- SVC signalling
static(2)-- circuit was configured}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Identify the last source of the circuit's creation."::={ cfrExtCircuitEntry 5}cfrExtCircuitMulticast OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Indicate if this DLCI is a multicast DLCI."::={ cfrExtCircuitEntry 6}cfrExtCircuitRoutedDlci OBJECT-TYPESYNTAX DlciNumber
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The routed DLCI to pair up with this DLCI
for switching function. NOTE: Value zero (0)
indicates that there is no such routed DLCI
corresponding to this DLCI."::={ cfrExtCircuitEntry 7}
cfrExtCircuitRoutedIf OBJECT-TYPESYNTAXInterfaceIndexMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The interface for the routed DLCI that pairs up
with this DLCI for switching. Value greater than 0
is the InterfaceIndex for that interface. Value
zero (0) indicates that there is no such routed DLCI
corresponding to this DLCI."::={ cfrExtCircuitEntry 8}cfrExtCircuitUncompressIns OBJECT-TYPESYNTAXCounter32UNITS"octets"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Number of inbound octets of the data packets,
accounted at Frame Relay level after FRF.9
payload decompression is applied. In the case of
non-FRF.9, this value could be identical to
frCircuitReceivedOctets, unless otherwise noted."::={ cfrExtCircuitEntry 9}cfrExtCircuitUncompressOuts OBJECT-TYPESYNTAXCounter32UNITS"octets"MAX-ACCESSread-only
STATUScurrentDESCRIPTION"Number of outbound octets of the data packets,
accounted at Frame Relay level before FRF.9
payload compression is applied. In the case of
non-FRF.9, this value could be identical to
frCircuitSentOctets, unless otherwise noted."::={ cfrExtCircuitEntry 10}cfrExtCircuitFECNOuts OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Total number of frames sent out to the network
indicating forward congestion."::={ cfrExtCircuitEntry 11}cfrExtCircuitBECNOuts OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Total number of frames sent out to the network
indicating backward congestion."::={ cfrExtCircuitEntry 12}cfrExtCircuitMinThruputOut OBJECT-TYPESYNTAXInteger32(9600..1544000)
UNITS"bits per second"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Circuit's outgoing minimal Throughput based on
configuration."::={ cfrExtCircuitEntry 13}cfrExtCircuitMinThruputIn OBJECT-TYPESYNTAXInteger32(9600..1544000)UNITS"bits per second"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Circuit's incoming minimal Throughput based on
configuration."::={ cfrExtCircuitEntry 14}cfrExtCircuitBcastPktOuts OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Total number of broadcast packets sent out to the
network."
::={ cfrExtCircuitEntry 15}cfrExtCircuitBcastByteOuts OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Total number of bytes sent out to the network in
broadcast packets."::={ cfrExtCircuitEntry 16}cfrExtCircuitBandwidth OBJECT-TYPESYNTAXInteger32(0..16777215)UNITS"bits per second"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Bandwidth of the virtual circuit, acquired from
Cisco typed LMI Full Status message."::={ cfrExtCircuitEntry 17}cfrExtCircuitShapeByteLimit OBJECT-TYPESYNTAXInteger32(125..2147483647)UNITS"octets"MAX-ACCESSread-only
STATUScurrentDESCRIPTION"Maximum number of tokens a token bucket can hold in any
time interval in case of traffic shaping."::={ cfrExtCircuitEntry 18}cfrExtCircuitShapeInterval OBJECT-TYPESYNTAXInteger32(10..125)UNITS"milliseconds"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Committed rate measurement interval."::={ cfrExtCircuitEntry 19}cfrExtCircuitShapeByteIncrement OBJECT-TYPESYNTAXInteger32(125..2147483647)UNITS"octets"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Number of tokens added into the token bucket per time
interval in case of traffic shaping."::={ cfrExtCircuitEntry 20}
cfrExtCircuitShapePkts OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Total number of packets that went through traffic
shaping."::={ cfrExtCircuitEntry 21}cfrExtCircuitShapeBytes OBJECT-TYPESYNTAXCounter32UNITS"octets"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Total number of bytes that went through traffic
shaping."::={ cfrExtCircuitEntry 22}cfrExtCircuitShapePktsDelay OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Total number of packets that were delayed by the
traffic shaper."::={ cfrExtCircuitEntry 23}
cfrExtCircuitShapeBytesDelay OBJECT-TYPESYNTAXCounter32UNITS"octets"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Total number of bytes that were delayed by the
traffic shaper."::={ cfrExtCircuitEntry 24}cfrExtCircuitShapeActive OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Shows whether shaping is active or not."::={ cfrExtCircuitEntry 25}cfrExtCircuitShapeAdapting OBJECT-TYPESYNTAXINTEGER{none(1),becn(2),foreSight(3)}MAX-ACCESSread-onlySTATUScurrent
DESCRIPTION"Type of Adaptive Shaping configured.
none(1) - No adaptive shaping configured
becn(2) - Backward Explicit Congestion Notification
foreSight(3) - ForeSight is the network traffic control
software used in Cisco WAN switches"::={ cfrExtCircuitEntry 26}cfrExtCircuitTxDataRate OBJECT-TYPESYNTAXINTEGER(1..45000000)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The average rate (bytes/second) at which data is
transmitted in this circuit. "::={ cfrExtCircuitEntry 27}cfrExtCircuitTxPktRate OBJECT-TYPESYNTAXINTEGER(1..45000000)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The average number of packets sent in a second in this
circuit."::={ cfrExtCircuitEntry 28}
cfrExtCircuitRcvDataRate OBJECT-TYPESYNTAXINTEGER(1..45000000)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The average rate (bytes/second) at which data is
received in this circuit. "::={ cfrExtCircuitEntry 29}cfrExtCircuitRcvPktRate OBJECT-TYPESYNTAXINTEGER(1..45000000)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The average number of packets received in a second in
this circuit. "::={ cfrExtCircuitEntry 30}-- end circuit subgroup }-- Mapping sub-group {cfrMapTable OBJECT-TYPESYNTAXSEQUENCEOF CfrMapEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION
"Table of protocols and addresses mapping
information of FR virtual circuit."::={ cfrMapObjs 1}cfrMapEntry OBJECT-TYPESYNTAX CfrMapEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Each entry of the table contains one mapping
information of a Frame Relay virtual circuit."INDEX{ frCircuitIfIndex, frCircuitDlci, cfrMapIndex }::={ cfrMapTable 1}
CfrMapEntry ::=SEQUENCE{
cfrMapIndex INTEGER,
cfrMapProtocol CfrMapProtocols,
cfrMapAddress OCTETSTRING(SIZE(0..64)),
cfrMapType INTEGER,
cfrMapEncaps INTEGER,
cfrMapBroadcast TruthValue,
cfrMapPayloadCompress TruthValue,
cfrMapTcpHdrCompress INTEGER,
cfrMapRtpHdrCompress INTEGER,
cfrMapPayloadCompressType INTEGER}cfrMapIndex OBJECT-TYPESYNTAXINTEGER(1..999)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"An arbitrary Index to the mapping information
associated with a certain circuit. The maximum
value is arbitrarily picked which is considered
sufficient for usual configuration."::={ cfrMapEntry 1}cfrMapProtocol OBJECT-TYPESYNTAX CfrMapProtocols
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Mapping protocol for this circuit."::={ cfrMapEntry 2}cfrMapAddress OBJECT-TYPESYNTAXOCTETSTRING(SIZE(0..64))
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Mapping protocol address at remote end for
this DLCI.
NOTE: For point-to-point DLCI, the string is fixed
to be point-to-point."::={ cfrMapEntry 3}cfrMapType OBJECT-TYPESYNTAXINTEGER{static(1),dynamic(2),svc(3)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Type for the map creation."::={ cfrMapEntry 4}cfrMapEncaps OBJECT-TYPESYNTAXINTEGER{ietf(1),-- following IETF specifications-- (RFC 1490 as up to date)
cisco(2)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Indication of the encapsulation type for this
mapping protocol."::={ cfrMapEntry 5}cfrMapBroadcast OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Broadcast enabled or disabled."::={ cfrMapEntry 6}cfrMapPayloadCompress OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-onlySTATUSdeprecated-- obsoleted by cfrMapPayloadCompressTypeDESCRIPTION"Indicate if payload compression is enabled."::={ cfrMapEntry 7}cfrMapTcpHdrCompress OBJECT-TYPESYNTAXINTEGER
{inapplicable(1),passive(2),active(3)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"TCP header compression type, if applicable."::={ cfrMapEntry 8}cfrMapRtpHdrCompress OBJECT-TYPESYNTAXINTEGER{inapplicable(1),passive(2),active(3)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"RTP header compression type, if applicable.
The value 'passive' means that the header of an
outgoing RTP/IP packet is compressed only if an
incoming RTP/IP packet had a compressed header.
The value 'active' means the header of every outgoing
RTP/IP packet is compressed."::={ cfrMapEntry 9}cfrMapPayloadCompressType OBJECT-TYPESYNTAXINTEGER{inapplicable(1),cisco(2),-- Cisco proprietary FR packet--- by-packet payload compressionfrf9Software(3),-- FRF.9 software payload compressionfrf9Hardware(4)-- FRF.9 hardware payload compression}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"FR payload compression type, if applicable.
FRF.9 is the Frame Relay Forum Implementation Agreement
on FR payload compression. The compression can be done
by either software or hardware (when equipped with the
supporting hardware), depending on configuration."REFERENCE"Frame Relay Forum document number FRF.9"::={ cfrMapEntry 10}-- end mapping subgroup }
-- SVC sub-group {
-- containing SVC spcific informationcfrSvcTable OBJECT-TYPESYNTAXSEQUENCEOF CfrSvcEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Table of FR SVC specific, descriptive
and statistics information."::={ cfrSvcObjs 1}cfrSvcEntry OBJECT-TYPESYNTAX CfrSvcEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Each entry of the table contains circuit information
specific to a Frame Relay Switched Virtual Circuit."INDEX{ frCircuitIfIndex, frCircuitDlci }::={ cfrSvcTable 1}
CfrSvcEntry ::=SEQUENCE{
cfrSvcAddrLocal OCTETSTRING(SIZE(0..64)),
cfrSvcAddrRemote OCTETSTRING(SIZE(0..64)),
cfrSvcThroughputIn Integer32,
cfrSvcMinThruputOut Integer32,
cfrSvcMinThruputIn Integer32,
cfrSvcCommitBurstIn Integer32,
cfrSvcExcessBurstIn Integer32,
cfrSvcIdleTime Integer32}-- For circuit (DLCI) outbound throughput and outbound Committed
-- and Excess Burst size, please refer to the following from
-- RFC1315 respectively:
-- frCircuitThroughput,
-- frCircuitCommittedBurst, and
-- frCircuitExcessBurstcfrSvcAddrLocal OBJECT-TYPESYNTAXOCTETSTRING(SIZE(0..64))MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Local E.164/X.125 address for the circuit."::={ cfrSvcEntry 1}cfrSvcAddrRemote OBJECT-TYPESYNTAXOCTETSTRING(SIZE(0..64))
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Remote E.164/X.125 address for the circuit."::={ cfrSvcEntry 2}cfrSvcThroughputIn OBJECT-TYPESYNTAXInteger32(9600..1544000)UNITS"bits per second"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Circuit's incoming throughput. For outgoing
throughput (commonly referred to as CIR) see
frCircuitThroughput per RFC1315."::={ cfrSvcEntry 3}cfrSvcMinThruputOut OBJECT-TYPESYNTAXInteger32(9600..1544000)UNITS"bits per second"MAX-ACCESSread-onlySTATUSdeprecated-- deprecated by
-- cfrExtCircuitMinThruputOutDESCRIPTION"Circuit's outgoing minimal Throughput."::={ cfrSvcEntry 4}cfrSvcMinThruputIn OBJECT-TYPESYNTAXInteger32(9600..1544000)UNITS"bits per second"MAX-ACCESSread-onlySTATUSdeprecated-- deprecated by-- cfrExtCircuitMinThruputInDESCRIPTION"Circuit's incoming minimal Throughput."::={ cfrSvcEntry 5}cfrSvcCommitBurstIn OBJECT-TYPESYNTAXInteger32(9600..1544000)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Circuit's incoming Committed Burst Rate.
See ANSI and/or ITU specifications for
definition and calculations. For outgoing
CBR, see frCircuitCommittedBurst per RFC 1315."::={ cfrSvcEntry 6}cfrSvcExcessBurstIn OBJECT-TYPESYNTAXInteger32(9600..2440000)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Circuit's incoming Excess Burst Rate.
See ANSI and/or ITU specifications for
definition and calculations. For outgoing
EBR, see frCircuitExcessBurst per RFC 1315."::={ cfrSvcEntry 7}cfrSvcIdleTime OBJECT-TYPESYNTAXInteger32UNITS"seconds"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Circuit's idle time period. If expires, the
circuit is cleared."::={ cfrSvcEntry 8}-- end SVC subgroup }-- Enhanced Link Management Interface(ELMI) sub-group {
-- ELMI is the protocol that learns QOS parameters(CIR,Bc,Be etc)
-- of a VC from the switch.
-- This sub group contains ELMI specific information.
cfrElmiIpAddr OBJECT-TYPESYNTAXIpAddressMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object represents the Management address of the
device used for address registration.
Network management station can send management
messages to this IP address. This can be
user configured address or the address of one of the
interfaces on the device. If address registration is
disabled then this will have a value of 0.0.0.0.
This object is accessible only if the ELMI protocol
is supported on the device"::={ cfrElmiObjs 1}cfrElmiTable OBJECT-TYPESYNTAXSEQUENCEOF CfrElmiEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Table of CISCO Frame Relay ELMI information that is
specific to CISCO implementation"::={ cfrElmiObjs 2}cfrElmiEntry OBJECT-TYPESYNTAX CfrElmiEntry
MAX-ACCESSnot-accessibleSTATUScurrent
DESCRIPTION"Each entry of the table contains information about a
physical interface. The table can be accessible only
if the device supports ELMI protocol and if LMI is
enabled on the interface."INDEX{ ifIndex }::={ cfrElmiTable 1}
CfrElmiEntry ::=SEQUENCE{
cfrElmiLinkStatus
INTEGER,
cfrElmiArStatus
INTEGER,
cfrElmiRemoteStatus
INTEGER}cfrElmiLinkStatus OBJECT-TYPESYNTAXINTEGER{enabled(1),disabled(2)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This variable states whether Enhanced Link Management
Interface(ELMI) protocol is enabled or not on a
frame relay interface."::={ cfrElmiEntry 1}
cfrElmiArStatus OBJECT-TYPESYNTAXINTEGER{enabled(1),disabled(2)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This variable states whether the Enhanced Link
Management Interface(ELMI) address registration(AR)
mechanism is enabled or not on a frame relay
interface. A value of 1 indicates ELMI AR is
supported on the interface. A value of 2 indicates
ELMI AR is supported but the user disabled the
exchange of IP address and ifIndex with the
neighboring device. This object doesn't have any
significance if cfrElmiLinkStatus is disabled
on the interface."::={ cfrElmiEntry 2}cfrElmiRemoteStatus OBJECT-TYPESYNTAXINTEGER{enabled(1),disabled(2)}MAX-ACCESSread-only
STATUScurrentDESCRIPTION"This variable states the Enhanced Link
Management(ELMI) status on the other end of the
interface. If cfrElmiLinkStatus is enabled on the
other end a value of 1 will be returned,
else 2 will be returned. This object doesn't have any
significance if cfrElmiLinkStatus is disabled on the
interface"::={ cfrElmiEntry 3}cfrElmiNeighborTable OBJECT-TYPESYNTAXSEQUENCEOF CfrElmiNeighborEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Table of CISCO Frame Relay Neighbor ELMI information
that is specific to CISCO implementation."::={ cfrElmiObjs 3}cfrElmiNeighborEntry OBJECT-TYPESYNTAX CfrElmiNeighborEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Each entry of the table contains information of the
neighboring device connected to a physical interface.
The entry will be present only if ELMI is enabled on
the neighboring device interface. If the value of the
cfrElmiRemoteStatus in the cfrElmiEntry is 1 then a
valid entry exists for the interface. If ELMI is not
supported on the remote end then, the neighbor
information for the interface will not be present"INDEX{ ifIndex }::={ cfrElmiNeighborTable 1}
CfrElmiNeighborEntry ::=SEQUENCE{
cfrElmiNeighborArStatus
INTEGER,
cfrElmiNeighborIpAddress
IpAddress,
cfrElmiNeighborIfIndex
InterfaceIndex,
cfrElmiNeighborVendorName
DisplayString,
cfrElmiNeighborPlatformName
DisplayString,
cfrElmiNeighborDeviceName
DisplayString}cfrElmiNeighborArStatus OBJECT-TYPESYNTAXINTEGER{notsupported(1),enabled(2),disabled(3)}
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This variable indicates the status of ELMI Address
registration(AR) on the neighboring device. A value
of 1 indicates ELMI AR is not supported on the
neighboring device. A value of 2 indicates ELMI AR is
enabled on the interface. A value of 3 indicates AR is
supported, but user disabled the exchange of IP
address and ifIndex with the neighbor."::={ cfrElmiNeighborEntry 1}cfrElmiNeighborIpAddress OBJECT-TYPESYNTAXIpAddressMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The Management IP address of the neighboring device
to which the other end of this interface is
connected. Network management system can use this
address to send management messages to the device.
If address registration is not supported on the
remote end then the value will be 0.0.0.0.
NMS uses this object in the topology discovery of the
network."::={ cfrElmiNeighborEntry 2}cfrElmiNeighborIfIndex OBJECT-TYPESYNTAXInterfaceIndex
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The Interface index of the neighboring device to
which this interface is connected. If the value of
cfrElmiNeighborArStatus is 2 then this will have a
valid value. If the value of cfrElmiNeighborArStatus
is 3 or 1 then value of this object will be 0. NMS
uses this object in the topology discovery of the
network."::={ cfrElmiNeighborEntry 3}cfrElmiNeighborVendorName OBJECT-TYPESYNTAXDisplayStringMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Vendor name of the neighboring device to which the
other end of this interface is connected."::={ cfrElmiNeighborEntry 4}cfrElmiNeighborPlatformName OBJECT-TYPESYNTAXDisplayStringMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Platform name of the neighboring device to which the
other end of this interface is connected."::={ cfrElmiNeighborEntry 5}cfrElmiNeighborDeviceName OBJECT-TYPESYNTAXDisplayStringMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Device name of the neighboring device to which the
other end of this interface is connected."::={ cfrElmiNeighborEntry 6}-- end ELMI sub-group }-- Fragmentation sub-group {cfrFragTable OBJECT-TYPESYNTAXSEQUENCEOF CfrFragEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Table of Frame Relay Fragmentation information.
These are specific to Cisco's implementation."::={ cfrFragObjs 1}cfrFragEntry OBJECT-TYPESYNTAX CfrFragEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION
"Each entry of the table contains details of
fragmentation configured on this circuit. "INDEX{ frCircuitIfIndex, frCircuitDlci}::={ cfrFragTable 1}
CfrFragEntry ::=SEQUENCE{
cfrFragSize INTEGER,
cfrFragType DisplayString,
cfrFragInPkts Counter32,
cfrFragOutPkts Counter32,
cfrFragInOctets Counter32,
cfrFragOutOctets Counter32,
cfrFragNotInPkts Counter32,
cfrFragNotOutPkts Counter32,
cfrFragNotInOctets Counter32,
cfrFragNotOutOctets Counter32,
cfrFragAssembledInPkts Counter32,
cfrFragAssembledInOctets Counter32,
cfrFragPreOutPkts Counter32,
cfrFragPreOutOctets Counter32,
cfrFragDroppedReAssembledInPkts Counter32,
cfrFragDroppedFragmentedOutPkts Counter32,
cfrFragTimeoutsIn INTEGER,
cfrFragOutOfSeqFragPkts Counter32,
cfrFragUnexpectedBBitSetPkts Counter32,
cfrFragSeqMissedPkts Counter32,
cfrFragInterleavedOutPkts Counter32}cfrFragSize OBJECT-TYPESYNTAXINTEGER(16..1600)UNITS"octets"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"cfrFragSize defines the payload size of a fragment
and it excludes the FR headers and any FR fragmentation
header."::={ cfrFragEntry 1}cfrFragType OBJECT-TYPESYNTAXDisplayStringMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Fragmentation type configured by the user. The types
supported are end-to-end, VoFR-cisco and VoFR."::={ cfrFragEntry 2}cfrFragInPkts OBJECT-TYPESYNTAXCounter32UNITS"packets"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Total number of frames received that have a
fragmentation header."::={ cfrFragEntry 3}cfrFragOutPkts OBJECT-TYPESYNTAXCounter32UNITS"packets"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Total number of fragments that are transmitted with a
fragmenation header."::={ cfrFragEntry 4}cfrFragInOctets OBJECT-TYPESYNTAXCounter32UNITS"octets"MAX-ACCESSread-onlySTATUScurrent
DESCRIPTION"Total number of bytes received in frames that have a
fragmentation header. The number of bytes include the
FR header."::={ cfrFragEntry 5}cfrFragOutOctets OBJECT-TYPESYNTAXCounter32UNITS"octets"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Total number of bytes that are transmitted in frames
with a fragmenation header. The number of bytes also
includes the FR header."::={ cfrFragEntry 6}cfrFragNotInPkts OBJECT-TYPESYNTAXCounter32UNITS"packets"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Total number of frames received that do not require
reassembly and therefore will not contain the
fragmentation header. This counter is valid only when
end-to-end fragmentation type is set."::={ cfrFragEntry 7}cfrFragNotOutPkts OBJECT-TYPESYNTAXCounter32UNITS"packets"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Total number of frames transmitted without fragmenting
and therefore will not contain the fragmentation header.
This counter is valid only when end-to-end fragmentation
type is set."::={ cfrFragEntry 8}cfrFragNotInOctets OBJECT-TYPESYNTAXCounter32UNITS"octets"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Total number of bytes received in frames that do not
require reassembly and therefore will not contain the
fragmentation header. This counter is valid only when
end-to-end fragmentation type is set."::={ cfrFragEntry 9}cfrFragNotOutOctets OBJECT-TYPESYNTAXCounter32UNITS"octets"MAX-ACCESSread-onlySTATUScurrent
DESCRIPTION"Total number of bytes transmitted in frames that are
not fragmented and therefore will not contain the
fragmentation header. This counter is valid only when
end-to-end fragmentation type is set."::={ cfrFragEntry 10}cfrFragAssembledInPkts OBJECT-TYPESYNTAXCounter32UNITS"packets"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Total number of fully reassembled frames. It also
counts the number of packets received without FR
fragmentation header (i.e. in un-fragmentated pkts)."::={ cfrFragEntry 11}cfrFragAssembledInOctets OBJECT-TYPESYNTAXCounter32UNITS"octets"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Total number of bytes received in fully reassembled
frames. It also counts the number of packets received
without FR fragmentation header (i.e.in un-fragmentated
pkts)."
::={ cfrFragEntry 12}cfrFragPreOutPkts OBJECT-TYPESYNTAXCounter32UNITS"packets"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Total number of frames fragmented and trasmitted. It
also counts the number of packets trasmitted without FR
fragmentation header (i.e. in un-fragmentated pkts)."::={ cfrFragEntry 13}cfrFragPreOutOctets OBJECT-TYPESYNTAXCounter32UNITS"octets"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Total number of bytes transmitted in fragmented frames.
It also counts the number of bytes trasmitted in frames
without FR fragmentation header (i.e. in un-fragmentated
pkts)."::={ cfrFragEntry 14}cfrFragDroppedReAssembledInPkts OBJECT-TYPESYNTAXCounter32UNITS"packets"
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Number of received fragments dropped for reasons such
as : running out of memory, receiving segments out of
sequence, receiving an unexpected frame with a B bit
set, timing out on a reassembling frame."::={ cfrFragEntry 15}cfrFragDroppedFragmentedOutPkts OBJECT-TYPESYNTAXCounter32UNITS"packets"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Number of fragments dropped because of running
out of memory."::={ cfrFragEntry 16}cfrFragTimeoutsIn OBJECT-TYPESYNTAXINTEGER(0..1000)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Number of reassemble timer timeouts for this circuit.
A frame requiring more than two minutes to fully
reassemble is dropped and timeout will be incremented
by one."::={ cfrFragEntry 17}cfrFragOutOfSeqFragPkts OBJECT-TYPESYNTAXCounter32UNITS"packets"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Indicates the total number of packets received with an
unexpected sequence number. All fragments being
reassembled are dropped. Start a new packet with the
received segment only if the B bit is set on the
segment. Otherwise the new segment is also dropped."::={ cfrFragEntry 18}cfrFragUnexpectedBBitSetPkts OBJECT-TYPESYNTAXCounter32UNITS"packets"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Number of fragments received in this circuit with
a B bit set. All fragments being reassembled are dropped
and a new packet is started with this segment."::={ cfrFragEntry 19}cfrFragSeqMissedPkts OBJECT-TYPE
SYNTAXCounter32UNITS"packets"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Number of fragments received in this circuit with
skipped sequence number."::={ cfrFragEntry 20}cfrFragInterleavedOutPkts OBJECT-TYPESYNTAXCounter32UNITS"packets"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Number of packets that have been interleaved between
segments."::={ cfrFragEntry 21}-- end Fragmentation sub-group }-- Connect sub-group {cfrConnectionTable OBJECT-TYPESYNTAXSEQUENCEOF CfrConnectionEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Table of Frame Relay/Frame Relay and Frame Relay/ATM
Network/Service Interworking connection information.
These are specific to Cisco's implementation."::={ cfrConnectionObjs 1}cfrConnectionEntry OBJECT-TYPESYNTAX CfrConnectionEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Each entry of the table contains information of a
connection that is established for Frame Relay/Frame
Relay and Frame Relay/ATM Network/Service Interworking."INDEX{ frCircuitIfIndex, frCircuitDlci}::={ cfrConnectionTable 1}
CfrConnectionEntry ::=SEQUENCE{
cfrConnName DisplayString,
cfrConnID INTEGER,
cfrConnState DisplayString,
cfrConnSegment1Name DisplayString,
cfrConnSegment1VCGroup DisplayString,
cfrConnSegment1Dlci DlciNumber,
cfrConnSegment2Name DisplayString,
cfrConnSegment2Vpi INTEGER,
cfrConnSegment2Vci INTEGER,
cfrConnServiceTranslation INTEGER,
cfrConnFrSscsDlci DlciNumber,
cfrConnEfciBit INTEGER,
cfrConnDeBit INTEGER,
cfrConnClpBit INTEGER}cfrConnName OBJECT-TYPESYNTAXDisplayStringMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The textual name of a for FR/FR or FR/ATM
Network/Service Interworking connection."::={ cfrConnectionEntry 1}cfrConnID OBJECT-TYPESYNTAXINTEGER(1..2000)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The numerical identifier of a FR/FR or FR/ATM
Network/Service Interworking connection."::={ cfrConnectionEntry 2}cfrConnState OBJECT-TYPESYNTAXDisplayString
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Status of a FR/FR or FR/ATM Network/Service
Interworking connection."::={ cfrConnectionEntry 3}cfrConnSegment1Name OBJECT-TYPESYNTAXDisplayStringMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The textual name used to identify the first segment of
a FR/FR or FR/ATM Network/Service Interworking
connection."::={ cfrConnectionEntry 4}cfrConnSegment1VCGroup OBJECT-TYPESYNTAXDisplayStringMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The textual name used to identify the VC-Group in the
first segment of a Frame Relay/ATM Network Interworking
(FRF.5)connection.
This field is not applicabe in case of,
FRF.8 (Frame Relay/ATM Service Interworking)
and
FR-FR connectione. "::={ cfrConnectionEntry 5}
cfrConnSegment1Dlci OBJECT-TYPESYNTAX DlciNumber
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The DLCI used as the first segment of a FR-FR or FR-ATM
Network/Service Interworking connection."::={ cfrConnectionEntry 6}cfrConnSegment2Name OBJECT-TYPESYNTAXDisplayStringMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The interface on which second segment of a FR-FR or
FR-ATM Network/Service Interworking connection is
configured."::={ cfrConnectionEntry 7}cfrConnSegment2Vpi OBJECT-TYPESYNTAXINTEGER(0..4095)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The value of VPI, in the ATM connection, used as the
second segment of a FR-ATM Network/Service Interworking
connection. In case of FR-FR connection, the same will
be used to display the DLCI used as the second segment."::={ cfrConnectionEntry 8}cfrConnSegment2Vci OBJECT-TYPESYNTAXINTEGER(0..4095)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The value of VCI, in the ATM connection, used as the
second segment of a FR-ATM Network/Service Interworking
connection. In case of FR-FR connection, this is not
supported."::={ cfrConnectionEntry 9}cfrConnServiceTranslation OBJECT-TYPESYNTAXINTEGER{serviceTranslationEnabled(1),serviceTranslationNotEnabled(2)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Shows whether Service Translation Mode is supported or
not. Translation Mode is the interworking of
internetworking (routed and/or bridged) protocols used
in FR-ATM Service PVC Interworking(FRF.8).
This is not supported in case of FRF.5 (FR-ATM network
Interworking) and FR-FR connections."::={ cfrConnectionEntry 10}cfrConnFrSscsDlci OBJECT-TYPESYNTAX DlciNumber
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The DLCI value used at the FR-SSCS layer. This is one of
connection multiplexing methods used in Frame Relay/ATM
Network Interworking.
Not supported in case of FRF.8 (FR-ATM Service PVC
Interworking) and FR-FR connections"::={ cfrConnectionEntry 11}cfrConnEfciBit OBJECT-TYPESYNTAXINTEGER{mapFecn(1),notMapFecn(2)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Shows whether the FECN field in the FR frame is mapped
to the ATM EFCI field of every cell generated out of the
FR frame. This is used to indicate congestion in FR to
ATM direction in case of Frame Relay/ATM Service PVC
Interworking.
Not supported in FRF.5 (Frame Relay/ATM Network
Interworking and FR-FR connections."::={ cfrConnectionEntry 12}cfrConnDeBit OBJECT-TYPESYNTAXINTEGER{noMapClp(1),mapClp(2),setDe0(3),setDe1(4)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The method of operation for loss priority mapping in the
B-ISDN to FR direction..
Not supported in case of FR-FR connection."::={ cfrConnectionEntry 13}cfrConnClpBit OBJECT-TYPESYNTAXINTEGER{setClpTo0AndCopyDeToFrsscsDe(1),
setClpTo1AndCopyDeToFrsscsDe(2),copyDeToFrsscsDeAndClp(3),copyDeToClp(4),setClp1(5),setClp0(6)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The method of operation used to map loss priority
mapping in the FR to ATM direction.
Not supported in case of FR-FR connection."::={ cfrConnectionEntry 14}-- end Conn subgroup }ciscoFrMIBConformance OBJECTIDENTIFIER::={ ciscoFrameRelayMIB 3}ciscoFrMIBCompliances OBJECTIDENTIFIER::={ ciscoFrMIBConformance 1}ciscoFrMIBGroups OBJECTIDENTIFIER::={ ciscoFrMIBConformance 2}
ciscoFrMIBCompliance MODULE-COMPLIANCESTATUSobsolete-- obsoleted by ciscoFrMIBCompliancesRev2DESCRIPTION"The compliance statement for entities which implement
this Cisco Frame Relay MIB."MODULE-- this moduleMANDATORY-GROUPS{ ciscoFrMIBGroup }::={ ciscoFrMIBCompliances 1}ciscoFrMIBCompliancesRev1 MODULE-COMPLIANCESTATUSobsolete-- obsoleted by ciscoFrMIBCompliancesRev2DESCRIPTION"The compliance statement for entities which implement
this Cisco Frame Relay MIB."MODULE-- this moduleMANDATORY-GROUPS{ ciscoFrMIBGroupRev1 }::={ ciscoFrMIBCompliances 2}ciscoFrMIBCompliancesRev2 MODULE-COMPLIANCESTATUSobsolete-- obsoleted by ciscoFrMIBCompliancesRev3DESCRIPTION"The compliance statement for entities which implement
this Cisco Frame Relay MIB."
MODULE-- this moduleMANDATORY-GROUPS{ ciscoFrLmiMIBGroup,
ciscoFrCircuitMIBGroup,
ciscoExtCircuitMIBGroup,
ciscoFrTsMIBGroup,
ciscoFrMapMIBGroup,
ciscoFrSvcMIBGroup }::={ ciscoFrMIBCompliances 3}ciscoFrMIBCompliancesRev3 MODULE-COMPLIANCESTATUSdeprecated-- deprecated by ciscoFrMIBCompliancesRev4DESCRIPTION"The compliance statement for entities which implement
this Cisco Frame Relay MIB."MODULE-- this moduleMANDATORY-GROUPS{ ciscoFrLmiMIBGroup,
ciscoFrCircuitMIBGroup,
ciscoExtCircuitMIBGroup,
ciscoFrTsMIBGroup,
ciscoFrMapMIBGroup,
ciscoFrSvcMIBGroup,
ciscoFrElmiMIBGroup}::={ ciscoFrMIBCompliances 4}
ciscoFrMIBCompliancesRev4 MODULE-COMPLIANCESTATUScurrentDESCRIPTION"The compliance statement for entities which implement
this Cisco Frame Relay MIB."MODULE-- this moduleMANDATORY-GROUPS{ ciscoFrLmiMIBGroup,
ciscoFrCircuitMIBGroup,
ciscoExtCircuitMIBGroup1,
ciscoFrTsMIBGroup,
ciscoFrMapMIBGroup,
ciscoFrSvcMIBGroup,
ciscoFrElmiMIBGroup1,
ciscoFrFragMIBGroup,
ciscoFrConnMIBGroup}::={ ciscoFrMIBCompliances 5}-- units of conformance:ciscoFrMIBGroup OBJECT-GROUPOBJECTS{
cfrLmiLinkstatus,
cfrLmiLinkType,
cfrLmiEnquiryIns,
cfrLmiEnquiryOuts,
cfrLmiStatusIns,
cfrLmiStatusOuts,
cfrLmiUpdateStatusIns,
cfrLmiUpdateStatusOuts,
cfrLmiStatusTimeouts,
cfrLmiStatusEnqTimeouts,
cfrLmiN392Dce,
cfrLmiN393Dce,
cfrLmiT392Dce,
cfrCircuitDEins,
cfrCircuitDEouts,
cfrCircuitDropPktsOuts,
cfrCircuitType,
cfrExtCircuitIfName,
cfrExtCircuitIfType,
cfrExtCircuitSubifIndex,
cfrExtCircuitMapStatus,
cfrExtCircuitCreateType,
cfrExtCircuitMulticast,
cfrExtCircuitRoutedDlci,
cfrExtCircuitRoutedIf,
cfrMapIndex,
cfrMapProtocol,
cfrMapAddress,
cfrMapType,
cfrMapEncaps,
cfrMapBroadcast,
cfrMapPayloadCompress,
cfrMapTcpHdrCompress,
cfrSvcAddrLocal,
cfrSvcAddrRemote,
cfrSvcThroughputIn,
cfrSvcMinThruputOut,
cfrSvcMinThruputIn,
cfrSvcCommitBurstIn,
cfrSvcExcessBurstIn,
cfrSvcIdleTime
}STATUSdeprecated-- obsoleted by ciscoFrMIBGroupRev1
DESCRIPTION"The compliance statement for entities which implement
this Cisco Frame Relay MIB."::={ ciscoFrMIBGroups 1}ciscoFrMIBGroupRev1 OBJECT-GROUPOBJECTS{
cfrLmiLinkstatus,
cfrLmiLinkType,
cfrLmiEnquiryIns,
cfrLmiEnquiryOuts,
cfrLmiStatusIns,
cfrLmiStatusOuts,
cfrLmiUpdateStatusIns,
cfrLmiUpdateStatusOuts,
cfrLmiStatusTimeouts,
cfrLmiStatusEnqTimeouts,
cfrLmiN392Dce,
cfrLmiN393Dce,
cfrLmiT392Dce,
cfrCircuitDEins,
cfrCircuitDEouts,
cfrCircuitDropPktsOuts,
cfrCircuitType,
cfrExtCircuitIfName,
cfrExtCircuitIfType,
cfrExtCircuitSubifIndex,
cfrExtCircuitMapStatus,
cfrExtCircuitCreateType,
cfrExtCircuitMulticast,
cfrExtCircuitRoutedDlci,
cfrExtCircuitRoutedIf,
cfrExtCircuitUncompressIns,
cfrExtCircuitUncompressOuts,
cfrMapIndex,
cfrMapProtocol,
cfrMapAddress,
cfrMapType,
cfrMapEncaps,
cfrMapBroadcast,-- removed cfrMapPayloadCompress, obsoleted by cfrMapPayloadCompressType
cfrMapTcpHdrCompress,
cfrMapRtpHdrCompress,
cfrMapPayloadCompressType,
cfrSvcAddrLocal,
cfrSvcAddrRemote,
cfrSvcThroughputIn,
cfrSvcMinThruputOut,
cfrSvcMinThruputIn,
cfrSvcCommitBurstIn,
cfrSvcExcessBurstIn,
cfrSvcIdleTime
}STATUSdeprecatedDESCRIPTION"A collection of objects providing router's
Frame Relay configuration and statistics
information that are additional to the IETF
standard Frame Relay DTE MIB."::={ ciscoFrMIBGroups 2}ciscoFrLmiMIBGroup OBJECT-GROUPOBJECTS{
cfrLmiLinkstatus, cfrLmiLinkType, cfrLmiEnquiryIns,
cfrLmiEnquiryOuts, cfrLmiStatusIns, cfrLmiStatusOuts,
cfrLmiUpdateStatusIns, cfrLmiUpdateStatusOuts,
cfrLmiStatusTimeouts, cfrLmiStatusEnqTimeouts,
cfrLmiN392Dce, cfrLmiN393Dce, cfrLmiT392Dce
}STATUScurrentDESCRIPTION"A collection of objects providing router's
Frame Relay LMI configuration and statistics
information either supplemental to the
frDlcmiTable of RFC 1315 or specific to Cisco's
implementation."::={ ciscoFrMIBGroups 3}ciscoFrCircuitMIBGroup OBJECT-GROUPOBJECTS{
cfrCircuitDEins, cfrCircuitDEouts,
cfrCircuitDropPktsOuts, cfrCircuitType
}STATUScurrentDESCRIPTION"A collection of objects providing information of a
circuit that are not included in frCircuitTable of
RFC1315 but are generic to Frame Relay."::={ ciscoFrMIBGroups 4}ciscoExtCircuitMIBGroup OBJECT-GROUPOBJECTS{
cfrExtCircuitIfName, cfrExtCircuitIfType,
cfrExtCircuitSubifIndex, cfrExtCircuitMapStatus,
cfrExtCircuitCreateType, cfrExtCircuitMulticast,
cfrExtCircuitRoutedDlci, cfrExtCircuitRoutedIf,
cfrExtCircuitUncompressIns, cfrExtCircuitUncompressOuts,
cfrExtCircuitFECNOuts, cfrExtCircuitBECNOuts,
cfrExtCircuitMinThruputOut, cfrExtCircuitMinThruputIn,
cfrExtCircuitBcastPktOuts, cfrExtCircuitBcastByteOuts,
cfrExtCircuitBandwidth
}STATUSdeprecatedDESCRIPTION"A collection of objects that provide Cisco
implementation specific FR circuit information.
This is a Cisco extension for the frCircuitTable
of RFC 1315."::={ ciscoFrMIBGroups 5}ciscoExtCircuitMIBGroup1 OBJECT-GROUPOBJECTS{
cfrExtCircuitIfName, cfrExtCircuitIfType,
cfrExtCircuitSubifIndex, cfrExtCircuitMapStatus,
cfrExtCircuitCreateType, cfrExtCircuitMulticast,
cfrExtCircuitRoutedDlci, cfrExtCircuitRoutedIf,
cfrExtCircuitUncompressIns, cfrExtCircuitUncompressOuts,
cfrExtCircuitFECNOuts, cfrExtCircuitBECNOuts,
cfrExtCircuitMinThruputOut, cfrExtCircuitMinThruputIn,
cfrExtCircuitBcastPktOuts, cfrExtCircuitBcastByteOuts,
cfrExtCircuitBandwidth, cfrExtCircuitTxDataRate,
cfrExtCircuitTxPktRate, cfrExtCircuitRcvDataRate,
cfrExtCircuitRcvPktRate
}STATUScurrentDESCRIPTION"A collection of objects that provide Cisco
implementation specific FR circuit information.
This is a Cisco extension for the frCircuitTable
of RFC 1315."::={ ciscoFrMIBGroups 13}ciscoFrTsMIBGroup OBJECT-GROUPOBJECTS{
cfrExtCircuitShapeByteLimit, cfrExtCircuitShapeInterval,
cfrExtCircuitShapeByteIncrement, cfrExtCircuitShapePkts,
cfrExtCircuitShapeBytes, cfrExtCircuitShapePktsDelay,
cfrExtCircuitShapeBytesDelay, cfrExtCircuitShapeActive,
cfrExtCircuitShapeAdapting
}STATUScurrentDESCRIPTION
"A collection of objects that provide information
about Frame Relay Traffic Shaping. These are
additional to the IETF standard Frame Relay DTE MIB."::={ ciscoFrMIBGroups 6}ciscoFrMapMIBGroup OBJECT-GROUPOBJECTS{
cfrMapIndex, cfrMapProtocol, cfrMapAddress,
cfrMapType, cfrMapEncaps, cfrMapBroadcast,
cfrMapTcpHdrCompress, cfrMapRtpHdrCompress,
cfrMapPayloadCompressType
}STATUScurrentDESCRIPTION"A collection of objects to provide mapping
information of a Frame Relay virtual circuit.
These are additional to the IETF standard
Frame Relay DTE MIB."::={ ciscoFrMIBGroups 7}ciscoFrSvcMIBGroup OBJECT-GROUPOBJECTS{
cfrSvcAddrLocal,
cfrSvcAddrRemote,
cfrSvcThroughputIn,
cfrSvcCommitBurstIn,
cfrSvcExcessBurstIn,
cfrSvcIdleTime
}STATUScurrent
DESCRIPTION"A collection of objects to provide circuit
information specific to a Frame Relay Switched
Virtual Circuit.This is in addition to the IETF
standard Frame Relay DTE MIB."::={ ciscoFrMIBGroups 8}ciscoFrElmiMIBGroup OBJECT-GROUPOBJECTS{
cfrElmiIpAddr, cfrElmiArStatus, cfrElmiRemoteStatus,
cfrElmiNeighborArStatus, cfrElmiNeighborIpAddress,
cfrElmiNeighborIfIndex, cfrElmiNeighborVendorName,
cfrElmiNeighborPlatformName, cfrElmiNeighborDeviceName
}STATUSdeprecatedDESCRIPTION"A collection of objects providing router's
ELMI information."::={ ciscoFrMIBGroups 9}ciscoFrElmiMIBGroup1 OBJECT-GROUPOBJECTS{
cfrElmiIpAddr, cfrElmiArStatus, cfrElmiRemoteStatus,
cfrElmiNeighborArStatus, cfrElmiNeighborIpAddress,
cfrElmiNeighborIfIndex, cfrElmiNeighborVendorName,
cfrElmiNeighborPlatformName, cfrElmiNeighborDeviceName,
cfrElmiLinkStatus
}STATUScurrentDESCRIPTION"A collection of objects providing router's
ELMI information."::={ ciscoFrMIBGroups 10}ciscoFrFragMIBGroup OBJECT-GROUPOBJECTS{
cfrFragSize, cfrFragType, cfrFragInPkts, cfrFragOutPkts,
cfrFragInOctets, cfrFragOutOctets, cfrFragNotInPkts,
cfrFragNotOutPkts, cfrFragNotInOctets, cfrFragNotOutOctets,
cfrFragAssembledInPkts, cfrFragAssembledInOctets,
cfrFragPreOutPkts, cfrFragPreOutOctets,
cfrFragDroppedReAssembledInPkts,
cfrFragDroppedFragmentedOutPkts,
cfrFragTimeoutsIn, cfrFragOutOfSeqFragPkts,
cfrFragUnexpectedBBitSetPkts, cfrFragSeqMissedPkts,
cfrFragInterleavedOutPkts
}STATUScurrentDESCRIPTION"A collection of objects providing router's
fragmentation information."::={ ciscoFrMIBGroups 11}ciscoFrConnMIBGroup OBJECT-GROUPOBJECTS{
cfrConnName, cfrConnID, cfrConnState, cfrConnSegment1Name,
cfrConnSegment1VCGroup, cfrConnSegment1Dlci,
cfrConnSegment2Name, cfrConnSegment2Vpi,
cfrConnSegment2Vci, cfrConnServiceTranslation,
cfrConnFrSscsDlci, cfrConnEfciBit,
cfrConnDeBit, cfrConnClpBit
}STATUScurrentDESCRIPTION"A collection of objects providing router's
fragmentation information."::={ ciscoFrMIBGroups 12}END